1st Garage Door Openers, Inc.
 BBB Business Review

 Genie Door Garage Door Openers and OverHead Door Openers and Parts

HOME

ABOUT US

CONTACT US

1-480-247-2094

Genie Garage Door Opener Parts from 1st Garage door Openers Inc.
Authorized Genie Dealer

Garage Door Openers Genei and OverHead Door

REMOTES

SAFETY BEAM SYSTEM

PARTS

KEYLESS ENTRY

SECODER BOARDS

WALL CONTROLS

ACCESSORIES

 

1st Garage Door Openers Inc.

For your convenience
All orders are shipped same or next day!!!
 

VISA, MASTERCARD, AMERICAN EXPRESS and DISCOVER

 
Company Information, Privacy,  Shipping and Warranty
Policy

GENIE AT-95 Remote

 ( 9 or 12 Switch & 390 frequency)

 

*************   WARNING   *************

            Moving Door can cause serious injury or death.

         DO NOT install transmitter unless the door operatorís safety reverse works as required by the door operatorís manual.

         Wall control must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts.

         Keep people clear of opening while door is moving.

         DO NOT allow children to play with the transmitter or door operator.

If safety reverse does not work properly:

         Close door then disconnect operator using the manual release handle.

         DO NOT use transmitter or door operator.

         Refer to Door and Door Operators Ownerís Manuals before attempting any repairs.

            Electrical Shock can cause serious injury or death.

         Power cord must be unplugged before attaching any wires,

         Be sure wire ends do not touch each other or other terminals.

If you have questions or if you need a manual, contact the distributor or manufacturer of the operator.

****************************************************************************

NOTE: This replacement remote controller will work with both our 9 switch and 12 switch security code systems, provided the 3 digit frequency number matches the existing unit. If these numbers do not match, the new remote controller will not open the door.

       INSTRUCTIONS FOR YOUR NEW REMOTE CONTROLLER

All remote controller and garage door opener security code switches must match to remotely control your garage door opener.

SETTING THE SECURITY CODE ON YOUR NEW REMOTE CONTROLLER

The Genie Model at-95 Remote Controller will selectively activate three different Genie devices.  This controller will operate up to three Genie garage doors or two Genie door plus a Genie gate opener, for instance.

NOTE:  All devices to be controlled must use the 390 frequency and all must use code switches but not punch-out keys.

         Remove screw from the back to open the Controller.  The TYPE switch is the small code block with only three switches.  The CODE switches are located in the larger code block numbered 1 thru 10.

  • As received, all CODE switches will be in up position.  Using the tip of a ballpoint pen, set switches randomly to the down position. (slide the switch actuator tab completely from one end of the slot to the other to change setting).

NOTE:  ONCE YOU HAVE MADE THIS SELECTION DO NOT CHANGE IT LATER ON WHEN ADDING A SECOND OR THIRD GENIE DEVICE TO BE CONTROLLED.

Your code block with dip switches can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. 6" x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop off cover to find code block with dip switches).

  • Look at the CODE switch in the device you wish to control. 
  • 9 CODE switch devices.  Set the device CODE switches numbered 1 thru 7 to match the settings of the switches numbered 1 thru 7 at the top of the CODE switch block of the Remote Controller. (ignore the other row numbers 1 thru 10 at the bottom of the remote controller CODE switch block.
  • Decide which remote controller pushbutton you want to use fro this device and then set the device CODE switches 8 and 9 and Remote Controller TYPE switch from the chart below:

Device CODE Switch

Remote Button Desired                 8            9          Remote Controller TYPE Switch

             Left                               UP            UP              Left switch to 9 position

            Center                          Down         UP              Center switch to 9 position

             Right                             UP         Down            Right switch to 9 position

  • Look at the CODE switch in the device you wish to control. 
  • 12 CODE switch devices.  Set the device CODE switches numbered 1 thru 10 to match the settings of the switches numbered 1 thru 10 at the bottom of the CODE switch block of the Remote Controller. (Ignore the other row numbers 1 thru 7 at the top of the remote controller CODE switch block).
  • Decide which remote controller pushbutton you want to use fro this device and then set the device CODE switches 11 and 12 and Remote Controller TYPE switch from the chart below:

Device CODE Switch

Remote Button Desired               8              9          Remote Controller TYPE Switch

               Left                             UP            UP           Left switch to 12 position

            Center                          Down         UP          Center switch to 12 position

             Right                             UP         Down         Right switch to 12 position

 

Home | Our Products | Remote Controls | Keyless Entry | Safe-T-Beam  | Repair Parts | Accessories | Secoder BoardsCoding Instructions | About Us | Site Index Order by Phone |
Contact Us / Ask Kevin

1st Garage Door Openers Inc.
Mesa, AZ 85203
1-480-247-2094
1-480-247-3498 Fax

imdoors.com- Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981.  Providing excellent customer service and assistance for over 25 years. We are a discount reseller of  garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community.   We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Aladdin, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. Brand names of Garage Door openers are registered trade names of the respective entities and are only used for reference.

     

Copyright © 2017 All Rights Reserved. No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.